Modbus protokoll rs485: Difference between revisions

Revision as of 21:56, 8 December 2019

Modbus Funktions Codes

Hex Data				Funktion
..	01	..	..	Lese Ausgangsbit Status
..	02	..	..	Lese Eingangsbit Status
..	03	..	..	Lese Holding-Register Analog Ausgang
..	04	..	..	Lese Input-Register Analog Eingang
..	05	..	..	Schreibe Ausgangsbit
..	06	..	..	Schreibe Holding-Register Analog Ausgang
..	0F	..	..	* Funktion noch offen
..	10	..	..	* Funktion noch offen
..	15	..	..	Schreibe mehrfach Ausgangsbit
..	16	..	..	Schreibe mehrfach Holding-Register (Daten für >16-bit) Analog Ausgang
..	23	..	..	* Funktion noch offen

das sind wohl noch nicht alle Modbus Funktions Codes

Modbus Rtu 2

Hardware Resources: Data register address

 *   RS485 communication interface
 *   TTL communication interface
 *   2 optocoupler isolation input
 *   2 way optocoupler isolation output
 *   A user button
 *   A user LED
 *   A power indicator
 *   A STM32F030F4 microcontroller
 *   2 relay status indicators LED lights
 *   Power supply terminal interface (12V power supply)

Modbus RTU Instructions:

Baud rate: 9600 8 NONE 1

Hexadecimal send
hexadecimal receive

Operation steps:
1. Software settings communication baud rate
2. Set the address (communication using the device address, the default address is 01)

Set the address from 01 to 09 or from Broadcast to 09

Hex Byte	Funktion
01 10 00 00 00 01 02 00 09 66 56	Current address 01 is changed to 09
00 10 00 00 00 01 02 00 09 6B C6	Broadcast Address Modified to 09

Read Address

Hex Byte	Funktion
00 03 00 00 00 01 85 db	Send to Device
00 03 02 00 01 44 44	Receive from Device 01 for Address

Meaning of each byte:

Byte 1: address
byte 2: function
byte 3 4: register address
byte 5 6: register data
byte 7 8: CRC check

[address 1]

Switch Single

Hex Data								Funktion
Adresse	Funktion	Reghigh	Reglow	Data 1	Data 2	CRChigh	CRClow	Funktion
01	05	00	00	FF	00	8C	3A	0 relay ON
01	05	00	00	00	00	CD	CA	0 relay off
01	05	00	01	FF	00	DD	FA	No. 1 relay ON
01	05	00	01	00	00	9C	0A	No. 1 relay off
01	05	00	02	FF	00	2D	FA	No. 2 relay ON
01	05	00	02	00	00	6C	0A	No. 2 relay off

Switch all

Hex Data								Funktion
Adresse	Funktion	Reghigh	Reglow	Data 1	Data 2	Data 3	Data 4	CRChigh	CRClow	Funktion
01	0F	00	00	00	08	01	00	FE	95	Full off
01	0F	00	00	00	08	01	FF	BE	D5	Full on

01	01	00	00	00	08			BE	D5	Send : Read all relay states
01	01	01	00					51	88	Return : Relay fully closed
01	01	01	03					11	89	Return : All relays are on

01	02	00	00	00	08			79	CC	Send : Read all input switch status
01	02	01	00					A1	88	Return : 8 input states

Quelle - https://hacktronics.co.in/2-channel-relay-module/modbus-rtu-2-way-relay-output-2-way-input-switch-ttl-rs485-interface-communication

Modbus Rtu 4

Specifications:

 *   RS485 communication interface
 *   TTL communication interface
 *   4 optocoupler isolation input
 *   4 way optocoupler isolation output
 *   A user button
 *   A user LED
 *   A power indicator
 *   A STM32F030F4 microcontroller
 *   4 relay status indicators LED lights
 *   Power supply terminal interface (12V power supply)

Modbus RTU command

Baud Rate: 9600 8 NONE 1

Hex Byte	Funktion
00 06 40 00 00 01 5c 1b	Setting address is: 01
00 06 40 00 00 02 1c 1a	Setting address is: 02
00 03 40 00 00 01 90 1b	Read address
	Read the software version
00 03 00 04 00 01 c4 1a	[month] broadcast read (only by one device to address all practical, easy to test)
	Read the hardware version (PCB version)
00 03 00 04 00 01 c4 1a	broadcast read (only by one device to address all practical, easy to test)

[address 1]

Hex Byte	Funktion
01 05 00 01 01 00 9d 9a	No. 1 relay ON
01 05 00 01 00 00 9c 0a	No. 1 relay off

01 05 00 02 01 00 6d 9a	No. 2 relay ON
01 05 00 02 00 00 6c 0a	No. 2 relay off

01 05 00 03 01 00 3c 5a	No. 3 relay ON
01 05 00 03 00 00 3d ca	No. 3 relay off

01 05 00 04 01 00 8d 9b	No. 4 relay ON
01 05 00 04 00 00 8c 0b	No. 4 relay off

01 05 00 ff 00 00 fd fa	Quanmie
01 05 00 ff ff ff fc 4a	All light

[address 2]

Hex Byte	Funktion
02 05 00 01 01 00 9d a9	No. 1 relay ON
02 05 00 01 00 00 9c 39	No. 1 relay off

02 05 00 02 01 00 6d a9	No. 2 relay ON
02 05 00 02 00 00 6c 39	No. 2 relay off

02 05 00 03 01 00 3c 69	No. 3 relay ON
02 05 00 03 00 00 3d f9	No. 3 relay off

02 05 00 04 01 00 8d a8	No. 4 relay ON
02 05 00 04 00 00 8c 38	No. 4 relay off

02 05 00 ff 00 00 fd c9	Quanmie
02 05 00 ff ff ff fc 79	All light

[address 1]

Hex Byte	Funktion
01 01 00 01 00 04 6c 09	Send : No. 1 relay 1 channel status
	Return ......
01 01 00 02 00 04 9c 09	Send : No. 1 Relay 2 channel status
	Return ......
01 01 00 03 00 04 CD C9	Send : No. 1 Relay 3 channel status
	Return ......
01 01 00 04 00 04 7C 08	Send : No. 1 Relay 4 channel status

https://hacktronics.co.in/4-channel-relay-module/4-channel-relay-module-programmable-w-opto-isolated-rs485-stm8s103f3

DDS578R Energy Meter

MODBUS-RTU communication protocol Description:

1.the data format:
Address + function code + data + CRC check code

2.the register type
This meter uses two types of registers, individually addressed
The first is the data register, read-only, using the command code 0x04 to read.
The second category is the parameter register, readable and writable, using the command code 0x03
read, write parameters using 0x10

3.the data format
Float type data: Read the internal data within the meter in line with IEEE-754 standardv floating-point number, data format is 32-bit 4-byte single-precision floating-point data format.

4、Data register list

Data register address		Register Description
highByte	lowByte	Description	unit	Format	Mode
00	00	A phase voltage	V	Floating point	Read-only
00	02	B phase voltage	V	Floating point	Read-only
00	04	C phase voltage	V	Floating point	Read-only
00	08	A line current	A	Floating point	Read-only
00	0A	B line current	A	Floating point	Read-only
00	0C	C line current	A	Floating point	Read-only
00	10	Total active power	KWh	Floating point	Read-only
00	12	A phase active power	KWh	Floating point	Read-only
00	14	B phase active power	KWh	Floating point	Read-only
00	16	C phase active power	KWh	Floating point	Read-only
00	18	Total reactive power	KWh	Floating point	Read-only
00	1A	A phase reactive power	Var	Floating point	Read-only
00	1C	B phase areactive power	Var	Floating point	Read-only
00	1E	C phase reactive power	Var	Floating point	Read-only
00	2A	A phase power factor		Floating point	Read-only
00	2E	B phase power factor		Floating point	Read-only
00	2C	C phase power factor		Floating point	Read-only
00	36	frequency	frequency	Floating point	Read-only
01	00	Total active electricity power	KWh	Floating point	Read-only
04	00	Total reactive electricity power	KWh	Floating point	Read-only

@@ Line 1: / Line 1: @@
-=== Modbus Funktions Adressierung  ===
+=== Modbus Funktions Codes ===
 {| class="wikitable"
@@ Line 6: / Line 6: @@
 | ..  || 01  || ..  ||  ..  || Lese Ausgangsbit Status
 |-
-| ..  || 05  || ..  ||  ..  || Schreibe Ausgangsbit
+| ..  || 02  || ..  ||  ..  || Lese Eingangsbit Status
 |-
-| ..  || 15  || ..  ||  ..  || Schreibe mehrfach Ausgangsbit
+| ..  || 03  || ..  ||  ..  || Lese Holding-Register Analog Ausgang
-|-
-| ..  || 02  || ..  ||  ..  || Lese Eingangsbit Status
 |-
 | ..  || 04  || ..  ||  ..  || Lese Input-Register Analog Eingang
 |-
-| ..  || 03  || ..  ||  ..  || Lese Holding-Register Analog Ausgang
+| ..  || 05  || ..  ||  ..  || Schreibe Ausgangsbit
 |-
 | ..  || 06  || ..  ||  ..  || Schreibe Holding-Register Analog Ausgang
+|-
+| ..  || 0F  || ..  ||  ..  || * Funktion noch offen
+|-
+| ..  || 10  || ..  ||  ..  || * Funktion noch offen
+|-
+| ..  || 15  || ..  ||  ..  || Schreibe mehrfach Ausgangsbit
 |-
 | ..  || 16  || ..  ||  ..  || Schreibe mehrfach Holding-Register (Daten für >16-bit) Analog Ausgang
 |-
-| ..  || 10  || ..  ||  ..  || Funktion noch offen
+| ..  || 23  || ..  ||  ..  || *  Funktion noch offen
 |-
-| ..  || 0F  || ..  ||  ..  || Funktion noch offen
+|}
-|-
-|}
+* das sind wohl noch nicht alle Modbus Funktions Codes
 === Modbus Rtu 2 ===