No edit summary |
(Adding SL1 printer) |
||
| (3 intermediate revisions by 2 users not shown) | |||
| Line 1: | Line 1: | ||
== Table of printers == | == Table of printers == | ||
=== 2D === | |||
{| class=wikitable | {| class=wikitable | ||
| Line 6: | Line 8: | ||
! Network? | ! Network? | ||
! Recommended use | ! Recommended use | ||
|- | |||
|[[Printer/DCP-9055CDN|DCP-9055CDN]] | |||
|Color laser MFP (A4) | |||
|yes | |||
|printing & scanning | |||
|- | |- | ||
| [[Printer/HP_M276N|M276]] | | [[Printer/HP_M276N|M276]] | ||
| Line 16: | Line 23: | ||
| no | | no | ||
| printing on media unsuitable for lasers | | printing on media unsuitable for lasers | ||
|} | |||
=== 3D === | |||
{| class=wikitable | |||
! Name | |||
! Description | |||
! Network? | |||
! Recommended use | |||
|- | |||
|[[Ultimaker 3 extended]] | |||
|Dual Extruder 3D Printer | |||
|yes | |||
|printing | |||
|- | |||
|[[Makerbot Replicator 2]] | |||
|Single Extruder 3D Printer | |||
|no | |||
|printing | |||
|- | |||
|[[Archiv:Orcabot]] | |||
|Single Extruder 3D Printer | |||
|no | |||
|admire | |||
|- | |||
|Prusa SL1 | |||
|Small Resin 3D Printer | |||
|no | |||
|<s>making a mess</s>detailed parts | |||
|} | |} | ||
| Line 27: | Line 63: | ||
* Paper empty? Check "Schrank 1" second from the right, third from the left. | * Paper empty? Check "Schrank 1" second from the right, third from the left. | ||
* Only people who were given instructions are allowed to use the SL1 | |||
== Usage == | == Usage == | ||
Latest revision as of 13:11, 15 February 2024
Table of printers[edit | edit source]
2D[edit | edit source]
| Name | Description | Network? | Recommended use |
|---|---|---|---|
| DCP-9055CDN | Color laser MFP (A4) | yes | printing & scanning |
| M276 | Color laser MFP (A4) | yes | printing & scanning |
| DeskJet | Color inkjet printer (A4) | no | printing on media unsuitable for lasers |
3D[edit | edit source]
| Name | Description | Network? | Recommended use |
|---|---|---|---|
| Ultimaker 3 extended | Dual Extruder 3D Printer | yes | printing |
| Makerbot Replicator 2 | Single Extruder 3D Printer | no | printing |
| Archiv:Orcabot | Single Extruder 3D Printer | no | admire |
| Prusa SL1 | Small Resin 3D Printer | no |
Guidelines[edit | edit source]
- print on the smallest printer suitable
- before printing, turn printer on
- print single page to check your settings
- after printing, turn printer off
- donate money for your prints
- Paper empty? Check "Schrank 1" second from the right, third from the left.
- Only people who were given instructions are allowed to use the SL1
Usage[edit | edit source]
All network printers should announce themselves via zeroconf/avahi/bonjour. Simply start the printer and wait for it to appear on your system. You need to plug in the non-network printers to your device and set them up as you would setup any other printer.