The edit can be undone. Please check the comparison below to verify that this is what you want to do, and then publish the changes below to finish undoing the edit.
Latest revision | Your text | ||
Line 4: | Line 4: | ||
|project category=Hardware | |project category=Hardware | ||
|image=Micromoody front.jpg | |image=Micromoody front.jpg | ||
|status= | |status=beta | ||
|people={{U|derf}}, {{U|muzy}} | |people={{U|derf}}, {{U|muzy}} | ||
|source=https://github.com/muzy/MicroMoody{{!}}github | |source=https://github.com/muzy/MicroMoody{{!}}github | ||
Line 10: | Line 10: | ||
Ein Produkt des [https://wiki.raumzeitlabor.de/wiki/MicroMoody RaumZeitLabor]. | Ein Produkt des [https://wiki.raumzeitlabor.de/wiki/MicroMoody RaumZeitLabor]. | ||
[[File:Micromoody back.jpg|ATTiny85 und I²C (Pin 1 ist unten rechts)|200x200px| | [[File:Micromoody back.jpg|ATTiny85 und I²C (Pin 1 ist unten rechts)|200x200px|framed|right]] | ||
[[File:Micromoody circuit.png|Schaltplan|200x200px| | [[File:Micromoody circuit.png|Schaltplan|200x200px|framed|right]] | ||
[[File:Micromoody usb.jpg|USB → I²C → MicroMoody|200x200px| | [[File:Micromoody usb.jpg|USB → I²C → MicroMoody|200x200px|framed|right]] | ||
* ATTiny85 mit 8K Flash | * ATTiny85 mit 8K Flash | ||
* Tolle helle RGB-LED | |||
* Diverse voreingestellte Blinkenmodi | * Diverse voreingestellte Blinkenmodi | ||
* | * Stromversorgung per 6pin ISP-Kabel (5V) | ||
* Per I²C frei ansteuerbar (z.B. per [https://github.com/derf/vusb-i2c USB → I²C Bridge]) | |||
* Per I²C ansteuerbar | * Bald: [[SI2C]]-kompatibel | ||
{{U|derf}} hat Bausätze dazu, gibts gegen einen Unkostenbeitrag von 5€. | {{U|derf}} hat Bausätze dazu, gibts gegen einen Unkostenbeitrag von 5€. | ||
Bitte beachten: Im Bausatz ist kein Netzteil oder USB-Stromversorgungskabel enthalten, darum müsst ihr euch selber kümmern. | Bitte beachten: Im Bausatz ist kein Netzteil oder USB-Stromversorgungskabel enthalten, darum müsst ihr euch selber kümmern. Wir werden bald Moody-kompatible USB → I²C Bridges, die sich um Strom und Daten kümmern, zusätzlich anbieten. | ||
== Pinout == | == Pinout == | ||
Das Pinout auf dem Board (wenn man so draufschaut, dass die Beschriftung lesbar ist) ist um 180° rotiert. | |||
<pre> | <pre> | ||
┌───┐ | ┌───┐ | ||
(MISO) │1 2│ VCC | |||
(SCK) SDA │3 4│ SCL (MOSI) | |||
(RESET) │5 6│ GND | |||
└───┘ | └───┘ | ||
</pre> | </pre> | ||
Line 38: | Line 38: | ||
== Anleitung == | == Anleitung == | ||
[[File:Micromoody parts.jpg|Bauteile|200x200px| | [[File:Micromoody parts.jpg|Bauteile|200x200px|framed|none]] | ||
Folgende Bauteile sollte dein Bausatz enthalten: | Folgende Bauteile sollte dein Bausatz enthalten: | ||
Line 48: | Line 48: | ||
* 3x 100Ω SMD (R2, R3, R4) | * 3x 100Ω SMD (R2, R3, R4) | ||
* 1x 100nF SMD (C1) | * 1x 100nF SMD (C1) | ||
* | * 6pin ISP Header | ||
Es empfiehlt sich, | Es empfiehlt sich, zuerst den Kleinkram (C1, R1 bis R4) und dann den ATTiny zu löten. Anschließend von der anderen Seite die RGB-LED auflöten (so ausrichten wie aufgedruckt) und zu guter letzt den ISP-Header. Der ATTiny wird ohne Firmware eingepackt, d.h. bevor euer Gerät leuchtet, müsst ihr noch eine Firmware draufpacken. Dazu entweder {{U|derf}} ansprechen oder z.B. einen usbasp benutzen. | ||
Der ATTiny wird ohne Firmware | |||
<source lang="bash"> | <source lang="bash"> | ||
Line 64: | Line 58: | ||
> make program | > make program | ||
</source> | </source> | ||